From df80df8ba6775f6a4897624822ed622adf45be19 Mon Sep 17 00:00:00 2001 From: Philip Lampkin Date: Tue, 29 Dec 2020 21:23:01 -0600 Subject: Commented and cleaned up code --- .../Master_Random_LED_I2C.ino | 99 ++++++---------------- 1 file changed, 24 insertions(+), 75 deletions(-) (limited to 'Digital Photoreactor Controller Firmware/Test Sketchs') diff --git a/Digital Photoreactor Controller Firmware/Test Sketchs/Master_Random_LED_I2C/Master_Random_LED_I2C.ino b/Digital Photoreactor Controller Firmware/Test Sketchs/Master_Random_LED_I2C/Master_Random_LED_I2C.ino index 6c3e774..ac5f249 100644 --- a/Digital Photoreactor Controller Firmware/Test Sketchs/Master_Random_LED_I2C/Master_Random_LED_I2C.ino +++ b/Digital Photoreactor Controller Firmware/Test Sketchs/Master_Random_LED_I2C/Master_Random_LED_I2C.ino @@ -1,52 +1,32 @@ +//////////////////////////////////////////////////////////////////////////////////// +// I2C test program for Digital Photoreactor Controller using TinyWireS library // +// Run this Master program on an Arduino Uno. // +//////////////////////////////////////////////////////////////////////////////////// +// This test program is adapted from the TinyWireS stress test program // +// developed by Scott Hartog: https://github.com/rambo/TinyWire // +// // +// The master program picks a random number of bytes between 1 and 12. // +// It then sends that many bytes of randomd data to the AtTiny85 slave. // +// Then, the master reads that same number of bytes back from the slave. // +// The recieved data is then compared to the original transmitted data. // +// The results of this comparison are displayed in the serial monitor. // +// The process is then looped. // +// // +// BREADBOARD SETUP: // +// Arduino Uno R3 (D18/SDA) = I2C SDA // +// connect to SDA on slave with external pull-up (~4.7K) // +// Arduino Uno R3 (D19/SCL) = I2C SCL // +// connect to SCL on slave with external pull-up (~4.7K) // +// Arduino Uno R3 (D2) // +// connect to !RST on slave // +// Can alternatively connect !RST on slave to the Ardiuno "!RESET" pin // +// // +//////////////////////////////////////////////////////////////////////////////////// -// --------------------------------- -// Stress test program/example for TinyWireS I2C library. -// Run this master program on the Arduino Uno R3. -// Run the other slave program on the Attiny. -// --------------------------------- -// Written by Scott Hartog, 2/6/2016 -// This is the I2C master program which runs on on a regular Arduino -// (not a AtTiny). This program uses the regular Wire library from the Arduino IDE. -// -// It performs these steps in a loop: -// 1. picks a random number of bytes between 1 and 12 -// 2. sends that many bytes of random data to the AtTiny slave within -// a single Wire.beginTransmission() / Wire.write() / Wire.endTransmission() set -// 3. reads that same number of bytes back with a single Wire.requestFrom() call -// 4. compares the received data to the originally transmitted data -// 5. displays the number of requests, number of requests with mismatches, -// and enough of the data so that the operator can tell it's working. -// #include -// BREADBOARD SETUP: -// Arduino Uno R3 (D18/SDA) = I2C SDA -// connect to SDA on slave with external pull-up (~4.7K) -// Arduino Uno R3 (D19/SCL) = I2C SCL -// connect to SCL on slave with external pull-up (~4.7K) -// Arduino Uno R3 (D2) -// connect to !RST on slave -// Can alternatively connect !RST on slave to the Ardiuno "!RESET" pin - #define I2C_SLAVE_ADDR 0x26 // i2c slave address (38, 0x26) -/*#if defined(ESP8266) - // pins that work for Monkey Board ESP8266 12-E - // SCL=5, SDA=4 - #define SLAVE_RESET_PIN 2 - #define ALL_OK_LED_PIN 16 - #define OK_LED_PIN 14 - #define ERROR_LED_PIN 13 -#else - // pins that work for Micro Pro, Uno, Mega 2560 - // reference documentation for SCL and SDA pin locations - // Uno SDA=D18, SCL=D19 - #define SLAVE_RESET_PIN 6 - #define ALL_OK_LED_PIN 9 - #define OK_LED_PIN 7 - #define ERROR_LED_PIN 8 -#endif*/ - uint16_t count = 0; // total number of passes so far uint16_t error_count = 0; // total errors encountered so far @@ -54,33 +34,12 @@ char c_buf[64]; // for creating messages void setup() { - // set pin modes - /*pinMode(SLAVE_RESET_PIN,OUTPUT); // active low reset to slave device - pinMode(OK_LED_PIN,OUTPUT); // indicates last transaction matched - pinMode(ALL_OK_LED_PIN,OUTPUT); // indicates all transactions so far have matched - pinMode(ERROR_LED_PIN,OUTPUT); // indicates last transaction mismatched*/ // init the serial port Serial.begin(9600); - // print some useful pinnout info for the Arduino - //Serial.println(String("SCL:")+String(SCL)+String(", SDA:")+String(SDA)); - //Serial.println(String("MOSI:")+String(MOSI)+String(", SCK:")+String(SCK)); - // init the Wire object (for I2C) Wire.begin(); - - // init the i2c clock - // default is 100kHz if not changed - // Wire.setClock(400000L); // 400kHz - - // reset the slave - //digitalWrite(SLAVE_RESET_PIN, LOW); - //delay(10); - //digitalWrite(SLAVE_RESET_PIN, HIGH); - - // set the all okay pin high - //digitalWrite(ALL_OK_LED_PIN, HIGH); // wait for slave to finish any init sequence delay(2000); @@ -134,16 +93,6 @@ void loop() if (mismatch || (rand_byte_count != req_rtn)) { error_count++; - //digitalWrite(ERROR_LED_PIN, HIGH); - //digitalWrite(OK_LED_PIN, LOW); - // If there's ever an error, reset the ALL_OK_LED - // and it is not set again until the master resets. - //digitalWrite(ALL_OK_LED_PIN, LOW); - } - else - { - //digitalWrite(ERROR_LED_PIN, LOW); - //digitalWrite(OK_LED_PIN, HIGH); } // The rest of the program just displays the results to the serial port -- cgit v1.2.3