aboutsummaryrefslogtreecommitdiff
path: root/fabrication-and-operation-instructions
diff options
context:
space:
mode:
Diffstat (limited to 'fabrication-and-operation-instructions')
-rw-r--r--fabrication-and-operation-instructions/wpp-fabrication-operation.pdfbin43454467 -> 43454813 bytes
-rw-r--r--fabrication-and-operation-instructions/wpp-fabrication-operation.tex52
2 files changed, 34 insertions, 18 deletions
diff --git a/fabrication-and-operation-instructions/wpp-fabrication-operation.pdf b/fabrication-and-operation-instructions/wpp-fabrication-operation.pdf
index ad8666b..83b016f 100644
--- a/fabrication-and-operation-instructions/wpp-fabrication-operation.pdf
+++ b/fabrication-and-operation-instructions/wpp-fabrication-operation.pdf
Binary files differ
diff --git a/fabrication-and-operation-instructions/wpp-fabrication-operation.tex b/fabrication-and-operation-instructions/wpp-fabrication-operation.tex
index 5f3e4dd..b2545cf 100644
--- a/fabrication-and-operation-instructions/wpp-fabrication-operation.tex
+++ b/fabrication-and-operation-instructions/wpp-fabrication-operation.tex
@@ -523,35 +523,47 @@ Once finished, the WPP apparatus can be switched off by simply unplugging it and
\section{Documentation}
+WPP devices are trivial to document.
+Suggested below are the aspects of a WPP device that one should documented whenever a WPP device is used in an investigation.
+Documenting each of these aspects will allow for precise reproduction of the exact WPP device used within a study.
+
\subsection{Base and Photon Source} \label{SEC:doc-photon-source}
-Users should report the following for each photon source used:
+Users should report the following for each based and photon source used:
- (1) Max emission wavelength for LEDs.
- (2) Manufacturer and part number for LEDs.
- (3) Supplier and part number for LED star (if commercial).
+\begin{itemize}
+ \item Max emission wavelength for LEDs.
+ \item Manufacturer and part number for LEDs.
+ \item Supplier and part number for LED star (if commercial).
+\end{itemize}
-This information enables precise reproduction of WPP photon sources. Characterization of a photon source’s emission profile using a spectrometer is recommended but not required for reproduction. Emission profiles for commercial LEDs are supplied in part datasheets provided by manufacturers. A list of WPP-compatible LED stars exhibiting emission profiles across the visible range is provided in the project repository.
+This information enables precise reproduction of WPP photon sources. Characterization of a photon source’s emission profile using a spectrometer is recommended but not required for reproduction. Emission profiles for commercial LEDs are supplied in part datasheets provided by manufacturers.
\subsection{Reaction Module} \label{SEC:doc-reaction modules}
-Users should provide and report the following for each module used:
+Users should provide and report the following for each reaction module used:
- (1) Original CAD designs for both module parts.
- (2) 3D-printable models for both module parts.
- (3) Photos of each reaction vessel placement configuration.
- (4) Manufacturer and part number for reaction vessel.
+\begin{itemize}
+ \item Original CAD designs for both module parts.
+ \item 3D-printable models for both module parts.
+ \item Photos of each reaction vessel placement configuration.
+ \item Manufacturer and part number for reaction vessel.
+\end{itemize}
These provisions enable precise reproduction of reaction modules. Documenting the height a vessel is held above the photon source is recommended but not required for reaction module reproduction. All reaction modules provided in the project repository hold vessels a standardized 7 mm above the photon source.
-\subsection{Reactor Drivers} \label{SEC:doc-reactor-drivers}
+\subsection{Reactor Driver Electronics} \label{SEC:doc-reactor-drivers}
+
+As each reactor driver offers different configurational abilities, each requires documentation of different aspects for full reproduction.
\subsubsection{Analog Driver Board } \label{SEC:doc-analog-driver}
Users should report the following when an analog driver board is used:
- (1) Measured test point voltage.
- (2) Relative intensity at which LEDs are driven (0 to 100%).
+\begin{itemize}
+ \item Measured test point voltage.
+ \item Relative intensity at which LEDs are driven (0 to 100\%).
+\end{itemize}
These provisions enable precise reproduction of reaction conditions for transformations carried out using WPP devices fitted with analog driver boards.
@@ -559,17 +571,21 @@ These provisions enable precise reproduction of reaction conditions for transfor
Users should provide and document the following when a digital driver board is used:
- (1) Software used to operate the digital driver board, control unit and any other peripherals.
- (2) Relative intensity at which LEDs are driven (0 to 100%).
- (3) Relative fan speed (0 to 100%).
+\begin{itemize}
+ \item Software used to operate the digital driver board, control unit and any other peripherals.
+ \item Relative intensity at which LEDs are driven (0 to 100\%).
+ \item Relative fan speed (0 to 100\%).
+\end{itemize}
-These provisions enable precise reproduction of reaction conditions for transformations carried out using WPP devices fitted with digital driver boards
+These provisions enable precise reproduction of reaction conditions for transformations carried out using WPP devices fitted with digital driver boards.
\subsubsection{Simple Driver Circuit} \label{SEC:doc-simple-driver}
Users should report the following when a simple LED driver circuit is used:
- (1) Manufacturer and part number for LED driver.
+\begin{itemize}
+ \item Manufacturer and part number for LED driver.
+\end{itemize}
This information enables reproduction WPP devices fitted with the simple LED driver circuit.